Violectric DAC V800 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hudební vybavení Violectric DAC V800. Violectric DAC V800 User`s manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - DAC V800

1 DIGITAL-ANALOG CONVERTER DAC V800 (version 2.0) USER´s MANUAL

Strany 2 - Content

10GENERAL INFORMATION The VIOLECTRIC DAC V800 is a top-range D/A converter, distinguished by its very particular analog output stages. By means of t

Strany 3

11THE CASE The DAC V800's case as well as the front/rear panels are made of solid aluminium. This choice of material ensures high mechanical sta

Strany 4

12 THE DIGITAL INPUTS Four digital inputs are found on the unit's rear panel. They are denoted according to their electrical properties: balanc

Strany 5 - General Safety Instructions

13 THE DIGITAL OUTPUT The digital output is located on the rear panel. It is fitted with a Cinch socket according to IEC 958, unbalanced at 75 ohms

Strany 6 - RETIREZ LA FICHE MALE!!

14 THE ANALOG OUTPUTS The analog outputs are situated on the rear panel, fitted with electroni-cally balanced XLR terminals, as well as cinch sockets

Strany 7

15 THE MUTE BUTTON Output signal is fully cut by means of the “MUTE“ button. When engaged, the red “MUTE ON / ERROR“ LED will light up. RESAMPLING

Strany 8 - EMC emission might occur

16 - OFF lights up when the resampling function is deactivated. The digital input word is forwarded to the D/A converter without alteration. - x1 The

Strany 9 - Connection / Connectors

17 THE VOLUME CONTROL Analog output level is set by means of the "VOLUME“ control. Level control as such is effected within the D/A converter fo

Strany 10 - GENERAL INFORMATION

18Of course, all these settings are effected on the "active" side of the circuitry, thus leaving output impedance completely unaffected. By

Strany 11

19resampling module generates auxiliary clock signals needed for further processing of the digital signal within the unit. After the resampling stag

Strany 12 - THE DIGITAL INPUTS

2 Content Theme Page About Violectric 3 Safety Instructions 5 The Earth / Grounding Concept 7 Connection / Connectors 9 General 10 Operation 11

Strany 13 - THE DIGITAL OUTPUT

20 DISMANTLING / JUMPER SETTINGs Hint: Here we are talking about internal adjustments inside your HPA V181. You are in need of two screw drivers TOR

Strany 14 - INPUT SELECTION

21JUMPER SETTING DAC V800

Strany 15 - RESAMPLING

22TECHNICAL DATA DAC V800 All Measurement RMS unwtd., 20 Hz - 20 kHz, Sample-rate 48 kHz, digital level = 0 dBFs, analog output level = +15 dBu, Re

Strany 16

23EU CONFORMITY STATEMENT: We herewith declare that the following unit Name: VIOLECTRIC DAC V800 Serial No. : -alle - is in conformity with

Strany 17 - THE VOLUME CONTROL

24WARRANTY Since 1986 we are constructing and manufacturing sophisticated electronics for ambitious customers. Since the early beginnings we are try

Strany 18 - HOW IT ALL WORKS

3Cordial thanks for your decision in favour of a product ! is a trademark and product line of Lake People electronic GmbH. Lake People electronic

Strany 19

4How do devices get to the customer ? devices can be obtained from respective specialist suppliers. If there is none such accessible regionally, t

Strany 20 - PULL THE MAINS PLUG !!!

5General Safety Instructions WARNING For your protection, please read the following: Water, Liquids, Moisture: This appliance should not be used

Strany 21 - JUMPER SETTING DAC V800

6 Mains Fuse: The mains fuse of this appliance is soldered in place and accessible from the inside only!! A blown fuse may indicate an internal probl

Strany 22 - TECHNICAL DATA DAC V800

7 The Earth / Grounding Concept General GROUND-LIFT Jumper (accessible from the inside. Mind the SECURITY INSTRUCTIONS !! ): Ex-works this jumper

Strany 23 - EU CONFORMITY STATEMENT:

8 Unfortunately there is no general recommendation how to solve hum and jitter problems - or even minimize them. The best way to succeed is to check

Strany 24 - WARRANTY

9Connection / Connectors

Komentáře k této Příručce

Žádné komentáře